770.457.4676

Flats, blow outs, skids and longer stopping distances can all be the result of Chamblee folks driving around on under-inflated tires. Now, it’s hard to tell when a radial tire is under-inflated. If your manufacturer recommends 35 pounds of pressure, your sedan tire’s considered significantly under inflated at 26 pounds. The tire may not look low until it gets below 20 pounds.

New laws required manufacturers to include a Tire Pressure Monitoring System – or TPMS system – in all cars and light trucks by the 2008 model year. The system has a dashboard mounted warning light that goes off if one or more of the tires falls 25% below manufacturer’s pressure recommendations.

This technology has been used by Chamblee race car drivers for years. They are able to head off problems from under inflation by closely monitoring tire pressure on the track. It’s up to your car’s manufacturer to determine which of many TPMS systems available they’ll use to comply with the law.

Obviously, all of this doesn’t come free for Chamblee drivers. U.S. government studies have estimated the net costs. Of course, the TPMS system itself will cost something. Maintaining the system will have a cost, replacement of worn or broken parts and tire repair cost increases.

The costs are partially offset by savings in fuel and tire wear. There’s also a saving in property damage and travel delay. The net cost is estimated to be between $27 and $100. The government predicts fewer fatal accidents. They estimate that it will cost between three and nine million dollars for every life saved.

Your safety has always been a concern at J&L Auto Service. We want you on the road and accident free. We’ve traditionally provided things like tire rotations, snow tire mounting and flat fixes at a very low cost. We’ve been able to quickly and cheaply provide the service, and pass the low cost on to you as an expression of our good will.

That’s why we’re concerned about how you’ll perceive the changes that this new law will force. Every time a tire is changed: taken off to fix a flat, a new tire installed, a snow tire mounted; the J&L Auto Service service technician is now going to have to deal with the TPMS system.

Even a simple tire rotation will require that the monitor be reprogrammed to the new location of each tire. When a car battery is disconnected, the TPMS system will need to be reprogrammed. TPMS sensor batteries will need to be changed and failed parts replaced.

Like all other Chamblee service centers, here at J&L Auto Service we’ve had to purchase new scanning equipment to work with the TPMS sensors and to update expensive tire change equipment to better service wheels equipped with the new monitoring systems. Our J&L Auto Service service technicians have been thoroughly trained on many systems and new tire-changing techniques. All of this adds up to significantly increased cost to perform what was once a very inexpensive service for you.

So when you start so see the cost of tire changes, flat repairs and rotations going up at J&L Auto Service, please keep in mind that it’s because of government mandated safety equipment. We want to keep you safely on the road – and we’re committed to doing it at a fair price. This new safety equipment will help you avoid the most common types of vehicle failure in Chamblee, and possibly a catastrophic accident.

Under-inflated tires waste gas for lots of folks in the Sandy Springs area. Think how hard it is to walk in sand – you just have to work harder because of the resistance. When your tires don’t have enough air in them, their rolling resistance is dramatically increased and it simply takes more gas to get from Chamblee to Sandy Springs.

Always check your tire pressure when you gas up at one of our local Sandy Springs service stations. If they’re low – even just a little bit – bring them up to proper pressure. There’s a sticker on the inside of your driver’s door that gives the manufacturer’s recommended tire pressure.

And don’t rely on your tire pressure monitoring system to alert you to when you need more air. The TPMS system is set to warn you when pressure drops twenty percent below recommendations. That’s severely under inflated and you needed more air a long time ago. And if you have a slow leak – get it fixed right away at J&L Auto Service.

Get some air and save some gas.

Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Doraville Georgia.

Come see us at: 3667 North Peachtree Road Chamblee, Georgia 30341

Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.

Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.

The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at J&L Auto Service can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.

Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.

If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.

Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.

If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.

Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.

So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at J&L Auto Service and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.

Come by J&L Auto Service for a wheel bearing inspection, or for break service. Call for an appointment at 770-457-4676

At AutoNetTV we love doughnuts. So let’s pretend you have three doughnuts right in front of your for our discussion of upsizing wheels and tires. Hey, don’t eat them now – your going to need them later.

Many people want to accessorize their car – you know, make it theirs. One of the easiest ways to get a custom look is to get some new wheels. There are thousands of wheel designs out there to get you the look you want. And for many, that look includes bigger wheels. It used to be that cars came from the factory with 15 or 16 inch wheels. Now 16, 17 and even 18 inchers are standard. And the factories are offering optional wheel packages up to 20 inches or more.

Come in to J&L Auto Service to learn more about how you might upsize your wheels or tires.
You’ll find us at 3667 North Peachtree Road in Chamblee, Georgia 30341.

So let’s talk about what to consider when you want to upsize your wheels. It’s not exactly a do it yourself project, so you need to know a thing or two before you get started. The most important term to know is rolling diameter. The rolling diameter is simply the overall height of your tire. Unless you want to modify your suspension, you’ll want to keep your rolling diameter the same when you upsize your wheels.

Let’s think about those three golden doughnuts in front of you. They’re all about the same size. So if we pretend they’re tires, they would have the same rolling diameter. The doughnut hole is the size of the wheel. Now pretend we’ve made the hole bigger on some. That’s like having a bigger wheel – but the rolling diameter is the same.

It’s important to keep the rolling diameter the same for several reasons. First of all, if the tire is bigger, it might not fit in the wheel well. Next the speedometer, odometer and anti-lock brake system are all calibrated for the factory rolling diameter. In order for your anti-lock brakes to work properly, the rolling diameter must stay within 3% of the factory recommendation. If you ignore that, you run the risk that your anti-lock brakes won’t work properly.

Some cars today have electronically controlled suspension that will be negatively affected by changing the rolling diameter. Let’s think about the doughnuts again. You see, as the size of the wheel gets bigger, the sidewall gets shorter. The tire holds less air, so the sidewalls are made stiffer to compensate.

Low profile tires from top manufacturers use special compounds that give the sidewall the strength it needs without compromising ride quality. As you increase your wheel size, you’ll typically get a slightly wider tire. This means that you have a larger contact patch. The contact patch is part of the tire that contacts the road. Because there’s more rubber on the road, the vehicle will handle better. And braking distances will be shorter. A lot of people with trucks or SUV’s love the extra control.

You do have to watch out that the contact patch isn’t so big that the tires rub in turns or over bumps. What we’re talking about here is fitment. Your tire professional at J&L Auto Service can help you get this right. He’ll install your new wheels, add spacers if needed to make sure your brakes fit inside your new wheels, and get you rolling.

Also, if you drive off-road a lot, you may need a higher profile tire to protect your new rims. And make sure your new tires have the load rating you need if you tow a trailer or haul heavy loads. Again, your tire professional at J&L Auto Service knows how to help.

And don’t forget about tire pressure. If you have larger rims, your new tires will hold less air and they’ll need to run a slightly higher pressure. Forget that and you’ll wear your tires out fast. Finally, get an alignment after you get your new shoes. AutoNetTV wants you to safely have the look you want.

Everyone in the Atlanta area wants our tires to last as long as possible. Two ways to maximize tire life are wheel balancing and tire rotation.

When wheels are out of balance, they wobble a bit. That makes the tires wear in a cupping pattern. And they vibrate. To fix this, your service technician at J&L Auto Service puts weights on your wheels to balance them out. If a front wheel is out of balance you’ll feel it in the steering wheel. If it’s a rear wheel you’ll feel it through your seat.

That brings us to tire rotation. The front tires on a car wear out more quickly than the rear tires. As they push through turns from Chamblee to Doraville, the shoulders of the front tires wear down. So rotating front and rear tires allows them to all wear at about the same rate over the life of the tire.

Proper tire inflation will also help your tires last longer. Under-inflated tires wear excessively on the shoulder and may even overheat. This could cause tire damage or a blow out. Over-inflated tires wear to fast in the middle.

Four wheel drive trucks and SUV’s tend to wear their tires more unevenly so rotation is even more important with them. Give us a call to get our recommendation on your sedan.

See your owner’s manual or ask your service technician at J&L Auto Service for your recommended tire rotation schedule. It’s usually every 5,000 to 8,000 miles.

Tires cost a lot and they are one of the most critical safety components on your vehicle. Take care of them and they’ll take care of you.

J&L Auto Service
3667 North Peachtree Road
Chamblee, Georgia 30341
770.457.4676

So, everyone in the Chamblee Georgia area knows how great helium is – you know, party balloons, squeaky voices. But a lot of people around Chamblee still haven’t heard about the benefits of nitrogen in your tires, and how it can help your tires. Here’s some great advice from AutoNetTV, brought to you by J&L Auto Service.

Nitrogen has actually been around for a long time in the Chamblee Georgia commercial sector, but it’s just starting to catch on for private vehicles in the 30341 zip code area.

Why nitrogen in your tires? Air is air, right? Actually, it turns out there is a difference.

Contact J&L Auto Service to learn more about nitrogen in your tires
You can find us at:
3667 North Peachtree Road
Chamblee, Georgia 30341
Or call us at 770-457-4676

The heart of the matter is maintaining proper tire inflation. When your tires are properly inflated, they last longer, handle better and more safely, and save you money at the gas pump.

The problem is that tires filled in Chamblee with regular air can lose a pound and a half of air pressure every month. This just happens as the oxygen in the tire seeps out. So if you don’t check your pressure for a month or two, well, you can be significantly low – low enough to actually affect your handling, shorten tire life and waste money at the fuel pump.

How does nitrogen help? Regular air contains about 78% nitrogen. Nitrogen is the largest molecule in air. It’s dry and non-flammable. Air also contains 21% oxygen, which is smaller and seeps out of the tire three to four times faster than nitrogen.

So, a tire filled with nitrogen at J&L Auto Service will take about six months to lose as much pressure as regular air does in just one month. So it’s more forgiving for those who don’t check their pressure every week.

Also, when oxygen is at higher temperatures – like those inside your tire when you’ve been driving for awhile – it oxidizes the inside of your tire. Getting the oxygen out of your tire means that it’ll last longer.

Who’s using nitrogen? Well, let’s start with NASCAR and Indy. These racers like nitrogen’s ability to maintain consistent tire pressure and reduce tire temperatures under very demanding conditions. The US government requires all commercial aircraft to have nitrogen in their tires. NASA and the US Military use nitrogen. The mining industry has been filling those “humongous” tires with nitrogen for years. And semi trucks and trailers are starting to use nitrogen extensively.

You may have heard some detractors of nitrogen. But the studies and white papers from tire and vehicle manufacturers demonstrate that the technology really works.

In fact, a prominent consumer research group did a study where they filled some tires with air and some with nitrogen and stacked them outside for a year. They observed that the nitrogen filled tires did hold their pressure better, but they couldn’t see the economic benefit. But that particular test has very little to do with the real world. Most tires are actually holding up cars and they also get driven around and do a lot of work. So if nitrogen helps them last longer, saves gas and gives safer handling, it’s worth considering.

Learn more about nitrogen in your tires by watching our attached auto tips video from AutoNetTV.

So, when are your tires actually worn out? This is a question a lot of us in Chamblee Georgia ask ourselves. For many, the answer is ‘when they no longer pass a safety inspection’. But waiting that long can have a serious impact on your safety.

The U.S. Federal government doesn’t have any laws for tread depth, but 42 of the states, and all of Canada, do have regulations. They consider two-thirty-seconds of an inch to be the minimum legal tread depth. Two other states, including California, consider one-thirty-second to be the minimum and six states have no standards at all. Call us at J&L Auto Service (just call 770.457.4676 ) to find out what your requirements are in the Chamblee Georgia area.

Since 1968, U.S. law has required that a raised bar be molded across all tires. When tires are worn enough that this bar becomes visible, there’s just 2/32” of tread left. But does that older standard give you enough safety?

Well, Consumer Reports issued a call to consider replacing tires when tread reaches 4/32”. And the recommendation is backed by some very compelling studies. Now before we go into the studies, you need to know that the big issue is braking on wet surfaces.

We tend to think of the brakes doing all the stopping, but you also need to have effective tires to actually stop the car. When it’s wet or snowy in Chamblee Georgia, the tread of the tire is critical to stopping power.

Picture this: you’re driving over a water-covered stretch of road. Your tires actually need to be in contact with the road in order to stop. That means the tire has to channel the water away so the tire is actually contacting the road and not floating on a thin film of water – a condition known as hydroplaning. When there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

This is where the studies come in. We think you’ll be surprised. A section of a test track was flooded with a thin layer of water. If you laid a dime flat on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up truck were brought up to 70 mph and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths. First, they tested new tires. Then tires worn to legal limits. And finally, tires with 4/32” of tread were tested – this is the depth suggested by Consumer Reports

When the car with the legally worn tires had braked for the distance required to stop the car with new tires, it was still going 55 mph. The stopping distance was nearly doubled. That means if you barely have room to stop with new tires, then you would hit the car in front of you at 55 mph with the worn tires.

Now with the partially worn tires – at the depth recommended by Consumer Reports – the car was still going at 45 mph at the point where new tires brought the car to a halt. That’s a big improvement – you can see why Consumer Reports and others are calling for a new standard.

Now without going into all the details, let us tell you that stopping the truck with worn tires needed almost 1/10 of a mile of clear road ahead to come to a safe stop. Obviously this is really a big safety issue.

The tests were conducted with the same vehicles, but with different sets of tires. The brakes were the same, so the only variable, was the tires.

So, how do you know when your tires are at 4/32”? Well, it’s pretty easy. Just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

Now you may remember doing that with pennies. But a penny gives you 2/32” of an inch to Abraham Lincoln’s head. The quarter is the new standard – 4/32”.

Tires are a big ticket item and most people in Chamblee Georgia want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out? For us, and we would guess for many, the answer is “no”.

Well, Mr. Washington, let’s go out and look at my tires.

J&L Auto Service
3667 North Peachtree Road
Chamblee, Georgia 30341
770.457.4676

So you love our job, and your family life is great: You have achieved balance. But can you the same for your wheels? You can tell if your tires are out of balance by vibrations at higher speeds. If one of the front tires is out, you feel the vibration in the steering wheel. If it’s a back tire, you’ll feel the vibration in your seat.

Tires and wheels are pretty heavy. When a tire is mounted on a wheel, it is usually not perfectly balanced. So the tire technician will spin the tire on a machine to determine where it’s too heavy. He will then place weights on the wheels in strategic locations to balance it out. When a tire is out of balance, it actually bounces down the road instead of rolling smoothly. Since the average size tire rotates at about 850 revolutions per minute at 60 MPH, it is actually slamming into the pavement 14 times a second. That’s where you get your vibration.

Most people are surprised at how smoothly their car rides after balancing all four wheels.

Most high-quality tires hold their balance pretty well. They just get out of balance gradually with normal wear and tear. If you suddenly feel a vibration, it is probably because you lost a wheel balancing weight along the way. Definitely get a balance if you feel a vibration, change your rims or have a flat repaired. Putting off a needed balance job leads to excessive tire wear, wear to your shocks, struts, steering and suspension parts. wheel balancing not only improves your ride and handling, but also can save you some big repair bills and possibly an accident. Additionally, you will get better gas mileage.

Some people have their tires balanced at every rotation. Others do it every other time. Check your owners’ manual for your requirements, or ask your technician. Doing thus will put you on the path to mechanical wheel balance

.

We all know that under inflated tires wear out more quickly. Under-inflation is also a major cause of tire failure. More flats, blow outs, skids and longer stopping distances are all results of under-inflated tires.

It’s hard to tell when a radial tire is under-inflated. If your manufacturer recommends 35 pounds of pressure, your tire is considered significantly under inflated at 26 pounds. The tire may not look low until it gets below 20 pounds.

Uncle Sam to the rescue! A new federal law requires manufacturers to include a Tire Pressure Monitoring System – or TPMS system – in all vehicles by the 2008 model year.

Some 2006 and 2007 models already have TPMS. The system is a dashboard mounted warning light that goes off if one or more of the tires falls 25 % below the manufacturer’s pressure recommendations.

The law covers all passenger cars, SUVs, mini vans and pick up trucks. The system must also indicate if it has a malfunction. This technology has been used by race cars for years. They are able to head off problems from under inflation by closely monitoring tire pressure on the track. It’s up to your car’s manufacturer to determine which of many TPMS systems available they’ll use to comply with the law.

Obviously, all of this doesn’t come free. Government studies have estimated the net costs. Of course, the TPMS system itself will cost something. Maintaining the system will have a cost, replacement of worn or broken parts and tire repair cost increases. The net cost is estimated to be between $27 and $100.

The costs are partially offset by savings in fuel and tread wear. There is also a saving in property damage and travel delay. Also, the government predicts fewer fatal accidents. They estimate there will be between $3,000,000 to $9,000,000 for every life saved.

Your safety has always been a concern of your service center. They want you on the road and accident free. They’ve traditionally provided things like tire rotations, snow tire mounting and flat fixes at a very low cost. They’ve been able to quickly and cheaply provide the service, and they pass the low cost on to you as an expression of their good will. That’s why they’re concerned about how you’ll perceive the changes that this new law will force.

Every time a tire is changed: taken off to fix a flat, a new tire installed, or a snow tire mounted, the service technician is now going to have to deal with the TPMS system. Sensors will need to be removed and reinstalled. The sensors will have to be re-activated after the change. And, unfortunately, the very act of changing the tire will damage some sensor parts from time to time – it’s inevitable and can’t be avoided.

Even a simple tire rotation will require that the monitor be reprogrammed to the new location of each tire. When a car battery is disconnected, the TPMS system will need to be reprogrammed. TPMS sensor batteries will need to be changed and failed parts replaced.

And the service centers themselves will need to purchase new scanning equipment to work with the TPMS sensors and to update expensive tire change equipment to better service wheels equipped with the new monitoring systems.

Service technicians will have to be trained on many systems and new tire-changing techniques. All of this adds up to significantly increased cost to the service center to perform what was once a very inexpensive service for you. So when you start so see the cost of tire changes, flat repairs and rotations going up, please keep in mind that it’s because of government mandated safety equipment. Your service center just wants to keep you safely on the road – and it’s committed to do so at a fair price. The effects of the new law will take some time to sort out, but it will help you avoid the most common vehicle failure, and possibly a catastrophic accident.

When winter approaches in Chamblee Georgia, we break out the sweaters, coats, boots and mittens. We want to be ready for winter conditions. Your vehicle needs to be ready for winter as well. The last thing you want is to get stranded out in the cold. You need your vehicle to be safe and reliable. It’s a good idea to get caught up on any neglected maintenance items anytime – but the stakes are higher in the winter.

There are some specific things that we need to do in Chamblee Georgia to have our vehicle ready for winter. The most obvious is having the antifreeze checked. If the antifreeze level is too low, it can’t properly protect your engine, radiator and hoses from freezing. If your car does not seem to be making enough heat to keep you warm, your antifreeze level may be low or you could have a thermostat problem. Get it checked out. If you are due for a cooling system service, now is a perfect time to have it done.

In the cold months around Chamblee we always worry about being able to stop in time when it’s slick out. The first thing to remember is to slow down and allow yourself plenty of room to stop. Of course, you want your brakes to be working properly. A thorough brake inspection will reveal if the pads or any other parts need replacing. Check with your service consultant to see if it is time to replace your brake fluid. It accumulates water over time which really messes with your stopping power.

It is a really good idea to have your battery tested. A battery’s cranking power really drops with the temperature. If your battery is weak in the fall, it may not be up to winter. There is nothing like a dead battery in a snow storm.

Which leads us to an emergency kit. You should always have a blanket or something to keep you and your passengers warm if you get stranded. If you will be venturing away from civilization, pack more items such as food and water to help you survive. Keeping at least half a tank of gas is a good precaution if you get stuck and need to run the car to keep warm and it will help keep your gas lines from freezing up.

J&L Auto Service
3667 North Peachtree Road
Chamblee, Georgia 30341
770.457.4676

Winter in Chamblee Georgia always makes us think of our windshield wiper blades – usually during that first storm when they aren’t working right. That’s why it’s a really good idea to replace your blades in the fall before the winter storms. If you live where there’s a lot of snow and ice, you might want a special winter blade that resists freezing up. And be sure to have enough windshield washer fluid.

The final thing to consider is your tires. Any tire can lose pressure over time – up to one pound every six or eight weeks. For every 10 degrees the temperature drops you lose another pound of pressure. So if it was 80 degrees outside when you checked your tire pressure two months ago and now it’s 40 degrees out, you could be down 5 pounds of pressure. That’s enough to be a real safety issue and it wastes gas too. You may need special winter tires as well. Your tire professional can help you find the right tire design for your expected road conditions.

If you’re getting winter tires, it is always best to put them on all four wheels. If you are only getting two, have them put on the rear – even if you have a front-wheel drive or four-wheel drive vehicle.

This is a very important safety measure recommended by tire manufacturers. Sliding or fish-tailing on ice and snow is a matter of not having enough traction at the rear end. That is why your newest tires should always be on the rear.